Lesson 11: Introduction to Automotive Electrical Systems
How a car’s 12 V electrical system works: battery, chassis ground, alternator, starter motor, fuses, relays, and permanent versus ignition-switched power.
Builds on Lesson 10: Electrical Fault Finding and Troubleshooting
In this lesson you’ll learn
- How a 12 V vehicle system is arranged
- Battery positive, negative and chassis ground
- What the alternator and starter motor do
- How fuses and relays fit in
- Permanent versus ignition-switched power
- Common wiring terms: 30, 15, 31, 50, ACC
Lesson summary
- A car uses a 12 V battery (about 12.6 V when fully charged and at rest). Battery + feeds the fuse box; battery − is bolted to the body.
- The metal body and engine act as the ground (return) path, so most loads need only one feed wire.
- The alternator recharges the battery and powers the car while the engine runs, holding the system at about 14 V.
- The starter motor draws hundreds of amps for a few seconds, switched by a solenoid, not directly by the key.
- Permanent feeds (30) are always live; ACC, ignition (15) and start (50) feeds are live only in certain key positions.
- Every circuit is protected by a fuse near its source; high-current loads are switched by relays.
Lesson notes: Introduction to Automotive Electrical Systems
A written version of this lesson. The hands-on simulators are in the lesson itself.
A car is a big parallel circuit
Every load in a car is connected in parallel across the battery: each gets about 12 V, and each can be switched on its own (Lesson 6).
- Battery + feeds the fuse box through a thick main cable.
- Battery − is bolted to the car’s metal body. The body is the return path back to the battery: the chassis ground (or “earth”).
Try the headlight switch and the door. These work even with the key out.
Key idea: Using the body as the return path means each load needs only one feed wire, saving weight and cost. A loose or corroded ground connection is therefore a very common fault.
Starting and charging
- The starter motor turns the engine over. It draws hundreds of amps, so the key only switches a solenoid (a heavy-duty relay) that connects the motor to the battery.
- Once the engine runs, the engine-driven alternator takes over. It powers the electrical system and recharges the battery, at about 14 V.
Turn the key to ON, then hold START. Watch the system voltage and the starter current, then release.
Key idea: While cranking, the huge starter current makes the battery voltage dip (to about 10.7 V here), because the battery has a little internal resistance. With the alternator charging, the system rises to about 14 V.
Permanent and ignition-switched power
The ignition switch decides which feeds are live:
| Feed | Common name | Live when | Examples |
|---|---|---|---|
| 30 | Permanent / B+ | Always | Headlights, hazards, interior light |
| ACC | Accessory | ACC and ON | Radio, power socket |
| 15 | Ignition / IGN | ON and START | Instruments, fuel pump, engine computer |
| 50 | Start | START only | Starter solenoid |
| 31 | Ground | Always (0 V) | The return path to battery − |
Numbers like 30, 15, 31 and 50 come from the German DIN standard and appear on many wiring diagrams.
Key idea: Exact arrangements vary between manufacturers. For example, some cars switch headlights through the ignition, and many cut ACC while cranking. Always check the vehicle’s own wiring diagram.
Fuses and relays in the system
- The fuse box sits close to the battery, so each circuit’s fuse protects the whole length of its wiring (Lesson 9).
- High-current loads, such as headlights, the fuel pump, the horn and the cooling fan, are switched through relays, so dashboard switches only carry a small control current.
- The main battery and starter cables are usually not fused in older cars, so they must be well secured and insulated.
- Wires are identified by colour codes (e.g. RD for red, BK for black, BN for brown) and size, in mm² cross-section or AWG gauge. Thicker wire carries more current.
Key idea: Feed → fuse → switch or relay → load → ground. Almost every circuit in a car follows that pattern.
Worked examples
A starter motor uses about 1800 W while cranking a 12 V engine. Roughly what current does it draw? (Use the nominal 12 V.)
I = P ÷ VI = 1800 W ÷ 12 VI = 150 A: far too much for an ignition switch, which is why a solenoid is used
No experience needed. Answer as you go; you can always try again.