Series & Parallel CircuitsLesson 5: Understanding Series Circuits
Module 3: Series and Parallel Circuits

Lesson 5: Understanding Series Circuits

How series circuits work: why current is the same everywhere, how voltage is shared and how to add resistances, with a simulator and a fault-finding challenge.

  • About 25 minutes
  • 8 questions
  • 2 hands-on activities

Builds on Lesson 4: Understanding Ohm’s Law

In this lesson you’ll learn

  • What a series circuit is
  • Why current is the same everywhere in a series loop
  • How the supply voltage is shared between components
  • Total resistance: R = R₁ + R₂ + R₃
  • What happens when one component disconnects
  • Finding a failed bulb with a voltmeter
Lesson summary
  • A series circuit has one single path, so every component carries the same current.
  • Total resistance is the sum of the resistances: R = R₁ + R₂ + R₃.
  • The supply voltage is shared: the voltage drops across the components add up to the supply voltage.
  • A bigger resistance takes a bigger share of the voltage (V = I × R, with the same I).
  • Adding more components in series increases the total resistance and reduces the current.
  • One break anywhere stops the current everywhere. The full supply voltage then appears across the break.

Lesson notes: Understanding Series Circuits

A written version of this lesson. The hands-on simulators are in the lesson itself.

One path, one after another

In a series circuit, components are connected end to end, so there is only one path for the current.

Try 1, 2 and 3 bulbs. Watch the current and the brightness.

Key idea: Each extra bulb in series adds resistance, so the current falls and every bulb gets dimmer.

The current is the same everywhere

These three bulbs have different resistances: 2 Ω, 4 Ω and 6 Ω. The simulator measures the current in three places.

Charge can’t pile up or leak out of a single loop, so whatever flows in one place flows everywhere.

Key idea: In a series circuit, the same current flows through every component, whatever their resistances.

The voltage is shared

Each bulb has a voltage drop across it. Together, the drops add up to the battery voltage.

Give one bulb a bigger resistance and watch it take a bigger share.

Key idea: Each voltage drop is V = I × R. With the same current through each, a bigger resistance takes a bigger share of the voltage.

Total resistance in series

In series, resistances simply add up:

R(total) = R₁ + R₂ + R₃

Example: 2 Ω, 4 Ω and 6 Ω on a 12 V battery.
  1. Total resistance: 2 + 4 + 6 = 12 Ω
  2. Current: I = V ÷ R = 12 V ÷ 12 Ω = 1 A
  3. Voltage drops: 1 A × 2 Ω = 2 V, 1 A × 4 Ω = 4 V, 1 A × 6 Ω = 6 V
  4. Check: 2 + 4 + 6 = 12 V ✓

Key idea: Always check that the voltage drops add up to the supply voltage.

When one component disconnects

Tap a bulb in the diagram (or use its Remove button) to take it out of its holder.

Then look at the table: what happens to the current, and to the other bulbs?

Key idea: A single gap anywhere in a series circuit stops the current everywhere. The full supply voltage appears across the gap, which is how you can find it with a voltmeter.

Where you’ll find series connections

  • Switches and fuses are always wired in series with what they control or protect, so opening them stops the current to that load.
  • Old strings of fairy lights were wired in series: one failed bulb could put the whole string out.
  • Battery cells are connected in series to add their voltages: six 2.1 V lead-acid cells make a 12.6 V car battery.
  • Loads such as headlights are not wired in series with each other, because each needs the full supply voltage and must keep working if another fails. That needs parallel wiring.

Key idea: Series is perfect for control and protection. For running several loads, parallel is used instead.

Worked examples

  1. Three resistors, 3 Ω, 5 Ω and 4 Ω, are connected in series. What is the total resistance?

    R = R₁ + R₂ + R₃R = 3 Ω + 5 Ω + 4 ΩR = 12 Ω

  2. A 24 V supply is connected to 5 Ω and 7 Ω in series. What current flows?

    Total resistance: 5 Ω + 7 Ω = 12 ΩI = V ÷ R = 24 V ÷ 12 ΩI = 2 A

  3. In that same circuit (24 V, 5 Ω and 7 Ω in series, 2 A flowing), what is the voltage across the 7 Ω resistor?

    V = I × RV = 2 A × 7 Ω = 14 VCheck: the 5 Ω has 2 × 5 = 10 V; 10 + 14 = 24 V ✓

No experience needed. Answer as you go; you can always try again.