Measurement & TestingLesson 13: Reading Resistor Colour Codes
Module 10: Resistor Colour Codes

Lesson 13: Reading Resistor Colour Codes

How to read the resistor colour code (or color code): 4 and 5 band resistors, multipliers, tolerance and E12 values, with a decoder and a calculator.

  • About 25 minutes
  • 11 questions
  • 1 hands-on activity

Builds on Lesson 8: How to Use a Digital Multimeter

In this lesson you’ll learn

  • Why resistors are marked with colour bands
  • The colour code: digits, multipliers and tolerance
  • Reading 4-band and 5-band resistors
  • Which end to start reading from
  • Tolerance and the E12 standard values
  • Checking a resistor with a multimeter
Lesson summary
  • Each colour stands for a digit: black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9.
  • 4 bands: digit, digit, multiplier, tolerance. 5 bands: digit, digit, digit, multiplier, tolerance.
  • Start reading at the end away from the tolerance band (often gold or silver, and set apart).
  • Gold and silver multipliers (× 0.1 and × 0.01) are used for values below 10 Ω.
  • Tolerance gives the acceptable range: 1 kΩ ±5% can be anywhere from 950 Ω to 1050 Ω.
  • To check a resistor, measure it with the power off and at least one leg out of circuit.

Lesson notes: Reading Resistor Colour Codes

A written version of this lesson. The hands-on simulators are in the lesson itself.

Why resistors have colour bands

Most small resistors are too tiny to print a number on, and printed numbers would rub off or be hidden when the part is soldered in. Instead, the value is marked with coloured bands that can be read from any side.

This is a virtual resistor. Tap a band, then choose a colour, and watch the value change.

Key idea: The colour bands tell you the resistance in ohms and how accurate it is (its tolerance).

Each colour stands for a number

The colours always mean the same digits, from black = 0 to white = 9. From red to violet, they follow the order of the rainbow.

A memory aid for black, brown, red, orange, yellow, green, blue, violet, grey, white: “Better Be Right Or Your Great Big Venture Goes West”.

Key idea: Black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9.

Reading a 4-band resistor

On a 4-band resistor, each band has its own job:

  1. Bands 1 and 2 are the first two digits.
  2. Band 3 is the multiplier: what to multiply those digits by (in effect, how many zeros to add).
  3. Band 4 is the tolerance: how close the real value is guaranteed to be.

Yellow, violet, red, gold: digits 4 and 7 make 47. Red multiplies by 100, so the value is 47 × 100 = 4700 Ω (4.7 kΩ). Gold means ±5%.

Key idea: Digit, digit, multiplier, tolerance. Write the two digits, then multiply.

Which end do you start from?

A resistor looks the same either way round, so you need to know which end is band 1.

  • The tolerance band is usually set apart from the others, with a bigger gap. Start from the other end.
  • Gold and silver are never the first band, so if one end is gold or silver, start at the opposite end.
  • If you’re still unsure, read it both ways. Usually only one way gives a sensible, standard value. Or measure it.

Key idea: Read from the end furthest from the tolerance band. This one is brown, black, orange, gold: 10 × 1000 = 10 kΩ ±5%.

Gold and silver multipliers, and kΩ and MΩ

For values below 10 Ω, the multiplier band is gold (× 0.1) or silver (× 0.01). Green, blue, gold, gold: 56 × 0.1 = 5.6 Ω ±5%.

Large values are written with prefixes: 1 kΩ = 1000 Ω and 1 MΩ = 1,000,000 Ω. On circuit diagrams you will often see the letter used as the decimal point: 4k7 means 4.7 kΩ, 2M2 means 2.2 MΩ and 4R7 means 4.7 Ω.

Key idea: A gold multiplier divides by 10. Orange (× 1000) gives kilohms; green (× 100 000) and blue (× 1 000 000) give hundreds of kilohms and megohms.

5-band (precision) resistors

More accurate resistors use three digit bands, then the multiplier, then the tolerance. They are often ±1% (brown) or better.

Brown, black, black, red, brown: digits 1, 0, 0 make 100. Red multiplies by 100: 100 × 100 = 10 kΩ, and the brown tolerance band means ±1%. Switch the decoder between 4 and 5 bands and compare.

Some resistors have a sixth band at the end. It gives the temperature coefficient: how much the value changes as it heats up.

Key idea: 5 bands: digit, digit, digit, multiplier, tolerance.

Tolerance: how close is close enough?

No resistor is made to exactly its marked value. The tolerance says how far it may be from it. A 1 kΩ resistor with ±5% tolerance can be anywhere from 950 Ω to 1050 Ω and still be perfectly good.

Change the last band of this 1 kΩ resistor and watch the acceptable range change.

Key idea: Range = value ± (value × tolerance ÷ 100). For 1 kΩ ±5%: 5% of 1000 is 50, so 950 Ω to 1050 Ω.

Why 4.7 kΩ and not 4.5 kΩ? Standard values

Resistors aren’t made in every possible value. They come in standard series. The E12 series has 12 values in every decade, spaced so that their tolerance ranges roughly meet.

That is why you can buy 4.7 kΩ and 5.6 kΩ, but not 5 kΩ. More precise resistors use the E24, E48 or E96 series, with more values.

Key idea: E12 values: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82, times any power of ten.

Checking a resistor with a multimeter

Bands can be faded, scorched or hard to tell apart (red, orange and brown especially). A resistance measurement settles it.

  1. Make sure the circuit is switched off and disconnected. An ohmmeter must never be used on a live circuit.
  2. Lift at least one leg of the resistor out of the circuit. Otherwise other parts connected across it give the meter’s test current another path, and the reading will be wrong.
  3. Don’t hold both probe tips with your fingers. Your body adds a path in parallel, which lowers readings on high values.
  4. Compare the reading with the resistor’s tolerance range.

Key idea: Power off, one leg out of circuit, fingers off both probes, then compare the reading with the tolerance range.

From a value to the colour bands

Working the other way, from a value to its colours, is useful when picking a resistor out of a box. Type a value, choose the tolerance and the number of bands, and see the colours.

Key idea: Write the value with two significant digits (three for 5 bands), then count the zeros for the multiplier: 4700 = 47 and two zeros, so red (× 100).

Worked examples

  1. A resistor’s bands are brown, black, red, gold. What is its resistance in ohms?

    Digits: brown 1, black 0 → 10Multiplier: red × 10010 × 100 = 1000 Ω (1 kΩ)

  2. Red, red, brown, gold. What is the resistance in ohms?

    Digits: red 2, red 2 → 22Multiplier: brown × 1022 × 10 = 220 Ω

  3. Yellow, violet, gold, gold. What is the resistance in ohms?

    Digits: yellow 4, violet 7 → 47Multiplier: gold × 0.147 × 0.1 = 4.7 Ω

  4. Yellow, violet, orange, gold. What is the resistance in kilohms (kΩ)?

    Digits: yellow 4, violet 7 → 47Multiplier: orange × 100047 × 1000 = 47 000 Ω = 47 kΩ

  5. A 5-band resistor reads orange, orange, black, brown, brown. What is its resistance in ohms?

    Digits: orange 3, orange 3, black 0 → 330Multiplier: brown × 10330 × 10 = 3300 Ω (3.3 kΩ), ±1%

  6. A 220 Ω resistor has a silver tolerance band (±10%). What is the highest resistance it can have and still be within tolerance?

    10% of 220 Ω = 22 ΩHighest: 220 Ω + 22 Ω = 242 Ω(Lowest: 220 Ω − 22 Ω = 198 Ω)

No experience needed. Answer as you go; you can always try again.